Humidity Dictator Using DHT11 Sensor

DHT11 is a Humidity and Temperature Sensor, which generates calibrated digital output. DHT11 can be interface with any microcontroller like Arduino, Raspberry Pi, etc. and get instantaneous results. DHT11 is a low cost humidity and temperature sensor which provides high reliability and long term stability.


In this project, we will build a small circuit to interface Arduino with DHT11 Temperature and Humidity Sensor. One of the main applications of connecting DTH11 sensor with Arduino is weather monitoring.

We have already seen about humidity, relative humidity, humidity sensors and their types in this article.


DHT11 Sensor


The Schematics Circuit Diagram

Components Required
Arduino UNO [Buy Here]
DHT11 Temperature and Humidity Sensor
Breadboard (or perfboard)
Power supply
16 x 2 LCD Display [Buy Here]
10K Ohm Potentiometer
5K Ohm Resistor (1/4 W)
Connecting wires
Circuit Description
We will see the circuit design of DHT11 interfacing with Arduino. The DHT11 Humidity and Temperature sensor comes in two variants: just the sensor or a module.

The main difference is that the module consists of the pull – up resistor and may also include a power on LED. We have used a module in this project and if you wish to use the sensor itself, you need to connect a 5K Ω pull – up resistor additionally.

Coming to the design, the data pin of the DHT11 Sensor is connected to the Pin 11 of Arduino. A 16 x 2 LCD display is used to display the results. The control pins of LCD i.e. RS and E (Pins 4 and 6 on LCD) are connected to pins 4 and 5 of Arduino. The data pins of LCD i.e. D4 to D7 (pins 11 to 14 on LCD) are connected to pins 0 to 3 on LCD.

NOTE: For ease of connection, we have connected the DHT11 Sensor Module at the ICSP pins of the Arduino as it provides adjacent VCC, DATA and GND pins. This type of connection is not necessary and you can connect the data pin of sensor to normal Digital I/O pins.

Component Description
DHT11 Temperature and Humidity Sensor
DHT11 is a part of DHTXX series of Humidity sensors. The other sensor in this series is DHT22. Both these sensors are Relative Humidity (RH) Sensor. As a result, they will measure both the humidity and temperature. Although DHT11 Humidity Sensors are cheap and slow, they are very popular among hobbyists and beginners


DHT11 Sensor


The DHT11 Humidity and Temperature Sensor consists of 3 main components. A resistive type humidity sensor, an NTC (negative temperature coefficient) thermistor (to measure the temperature) and an 8-bit microcontroller, which converts the analog signals from both the sensors and sends out single digital signal.

This digital signal can be read by any microcontroller or microprocessor for further analysis.

DHT11 Pinout

DHT11 Humidity Sensor consists of 4 pins: VCC, Data Out, Not Connected (NC) and GND. The range of voltage for VCC pin is 3.5V to 5.5V. A 5V supply would do fine. The data from the Data Out pin is a serial digital data.

The following image shows a typical application circuit for DHT11 Humidity and Temperature Sensor. DHT11 Sensor can measure a humidity value in the range of 20 – 90% of Relative Humidity (RH) and a temperature in the range of 0 – 500C. The sampling period of the sensor is 1 second i.e.
DHT11 Application CircuitAll the DHT11 Sensors are accurately calibrated in the laboratory and the results are stored in the memory. A single wire communication can be established between any microcontroller like Arduino and the DHT11 Sensor.

Also, the length of the cable can be as long as 20 meters. The data from the sensor consists of integral and decimal parts for both Relative Humidity (RH) and temperature.

The data from the DHT11 sensor consists of 40 – bits and the format is as follows:

8 – Bit data for integral RH value, 8 – Bit data for decimal RH value, 8 – Bit data for integral Temperature value, 8 – Bit data for integral Temperature value and 8 – Bit data for checksum.

Working of the Project
A simple project is built using Arduino UNO and DHT11 Humidity and Temperature Sensor, where the Humidity and Temperature of the surroundings are displayed on an LCD display.

After making the connections, we need not do anything as the program will take care of everything. Although there is a special library for the DHT11 module called “DHT”, we didn’t use it. If you want to use this library, you need to download this library separately and add it to the existing libraries of Arduino.

The program written is based on the data timing diagrams provided in the datasheet. The program will make the Arduino to automatically read the data from the sensor and display it as Humidity and Temperature on the LCD Display.

CODE
#include
LiquidCrystal lcd(4, 5, 0, 1, 2, 3);
byte degree_symbol[8] =
{
0b00111,
0b00101,
0b001Applications
DHT11 Relative Humidity and Temperature Sensor can be used in many applications like:
HVAC (Heating, Ventilation and Air Conditioning) Systems
Weather Stations
Medical Equipment for measuring humidity
Home Automation Systems
Automotive and other weather control applications
Construction and Output Video11,
0b00000,
0b00000,
0b00000,
0b00000,
            0b00000
              };
int gate=11; 
volatile unsigned long duration=0;
unsigned char i[5];
unsigned int j[40];
unsigned char value=0;
unsigned answer=0;
int z=0;
int b=1;
void setup() 
{

lcd.begin(16, 2);
 lcd.print("Temp = ");
 lcd.setCursor(0,1);
 lcd.print("Humidity = ");
 lcd.createChar(1, degree_symbol);
 lcd.setCursor(9,0);
 lcd.write(1);
 lcd.print("C");
 lcd.setCursor(13,1);
 lcd.print("%");
}

void loop() 
{

 delay(1000);
 while(1)
 {
  delay(1000);
  pinMode(gate,OUTPUT);
  digitalWrite(gate,LOW);
  delay(20);
  digitalWrite(gate,HIGH);
  pinMode(gate,INPUT_PULLUP);//by default it will become high due to internal pull up
 // delayMicroseconds(40);

  
  duration=pulseIn(gate, LOW);
  if(duration <= 84 && duration >= 72)
  {
      while(1)
      {
        duration=pulseIn(gate, HIGH);
        
        if(duration <= 26 && duration >= 20){
        value=0;}
        
        else if(duration <= 74 && duration >= 65){
        value=1;}
        
        else if(z==40){
        break;}
        
        i[z/8]|=value<<(7- (z%8));
        j[z]=value;
        z++;
      }
    }
answer=i[0]+i[1]+i[2]+i[3];

if(answer==i[4] && answer!=0)
{
lcd.setCursor(7,0);
lcd.print(i[2]);
lcd.setCursor(11,1);
lcd.print(i[0]);
}

z=0;
i[0]=i[1]=i[2]=i[3]=i[4]=0;
 }
} 

Applications

  • DHT11 Relative Humidity and Temperature Sensor can be used in many applications like:
  • HVAC (Heating, Ventilation and Air Conditioning) Systems
  • Weather Stations
  • Medical Equipment for measuring humidity
  • Home Automation Systems
  • Automotive and other weather control applications 

Construction and Output Video

Video Loading......

Comments

Post a Comment